Charging 3-stage: constant current(MPPT), constant voltage(Absorption Voltage), floating charge. Selectable battery type Vented / Sealed / Gel / NiCd / Lithium battery (default is Sealed) (defined voltage for other battery by user). 1S, Dynamic response and recovery time 100us. In order to reduce the cost of electricity caused by high current, PV and battery each have two terminals.
Ensure that the solar input voltage exceeds 3v or is higher than the battery voltage. 12 Volt Battery Systems: Maximum PV input power 720 watts, recommended solar input voltage range 20 - 80 volts DC. 24 Volt Battery Systems: Maximum PV input power 1440 watts, recommended PV input voltage range 37 - 105 VDC. 36 volt battery system: 2100 watt maximum PV input, recommended PV input voltage range 50 - 150 volts DC.
48 volt battery system: 2800 watt maximum PV input, recommended PV input voltage range 72 - 150 volts DC. Install the switch between the controller and the battery.
Install a switch between the controller and the PV module. Check that the "+" and "-" of the PV module and the "+" and "-" of the battery are correctly connected. Turn on the battery switch first, then turn on the PV switch. ESC: Exit the setting without saving the data. UP: Scroll down, adjust the parameter by increasing the value.
DOWN: Scroll up, adjust the parameter by decreasing the value. ENTER: Short press to move to the next setting page, long press to exit the setting and save the data. BST - r: Pulse charge recovery voltage. The battery voltage must be higher than 12v for the controller to start.
Make sure that the solar input voltage exceeds 3v or the battery voltage. Hold the wiring correctly and do not change the wiring. Pay attention to the order of the terminal wiring. If it is a lead acid battery, if it is not professional, do not set any parameter, because in addition to the lithium battery, the controller also works well in the standard state.Do not connect solar inverters / generators / wind turbines to the controller. Install the controller indoors to prevent the components from entering the water. Maximum PV input voltage (voc): 180 V dc, the controller cannot work for a long time under this voltage, which will damage the controller.
Disconnect the battery and reconnect to save the configuration. 80A 100A MPPT solar charge controller· MPPT technology· 3-stage charging optimizes battery performance· Battery OVP? Reverse Polarity protection· Suitable for battery types such as sealed lead acid, vented gel and lithium battery, etc· Automatic battery voltage detection for 12V/24V/36V/48V· Easy to be mounted. 3-stage:ConstantCurrent(MPPT), ConstantVoltage, Floating.
12VSystem(DC8.7V-DC15.5V), 24VSystem(DC16V-DC31V). 12VSystem(16V), 24VSystem(32V)36VSystem(48V), 48VSystem(64V). 80A MPPT Solar Controller, Solar Charger Regulator 12V/24V/36V/48V Auto, Intelligent Regulator Charge Controller, Support Wide Range of Batteries. 80A MPPT Solar Charge Controller Features. Intelligent Maximum Power Point Tracking technology increases efficiency 25-30%.
3-Stage Charging: Constant current(MPPT);Absorption stage (Constant voltage) ; Float stage. Compatible for PV systemsin 12V/24/36V/48V. Integrated intelligent slot compatible with RS485/USB Communication. BTS:Battery temperature sensor automatically provides temperature compensation. Support wide range of lead-acid batteries including flooded, AGM, GEL, LEAD, Lithiumion, User-Defined batteries.
80A MPPT Solar Charge Controller. This solar charge controller is an advanced solar charger with maximum power point tracking. Applying intelligent MPPT algorithm, it allows solar charge controller to extract maximum power from solar arrays by finding the maximum power point of the array. The MPPT battery charging process has been optimized for long battery life and improved system performance. Self-diagnostics and electronic error protections prevent damage when installation errors or system faults occur.This charger also features multifunctional LCD with communication ports for remote battery temperature and voltage measurement. 80A MPPT Solar Controller Parallel Function. 1;Solar controller link order: first connect to battery; then connect to PV array; finally connect to load appliance. 2; Don't connect inverter, wind, alternator charger into the charge controller! Please connect the solar controller to the battery.
3;If solar PV input voltage lower 3V or lower than batteries' voltage. It may be appears to have been discontinued. 4; Parameter Setting:Floating voltage > Low voltage reconnect > Low voltage discharge.
5;When controller makes buzzing because the controller dissipate heat. It will be stop when temperature return to normal. 6;Don't let the positive (+) and negative (-) terminals of the battery touch each other. 80A MPPT Solar Charge Controller Package List? Solar charge controller x 1?
USB cable x 1 Battery temperature sensor cable x 1. 40A 30A 20A MPPT solar charge controller(Fan cooling).
12V/24V(auto detection);32V(setting). DSP processors technology ensure high. Protection: PV array short circuit. PV reverse polarity, Battery reverse polarity. Over charging, Output short circuit.ICharer MPPT 2420 2430 2440. 260W(12V) 260W(12V)/ 260W(12V) 260W(12V)/520W(12V). 16.8V-60V(12V) 33.6V. (24V) /16.8V-60V(12V) 33.6V-60V(24V)/16.8V-60V(12V)33.6V-60V(24V). Maintenance-free lead-acid battery, GEL, lead-acid Flooded battery :10.8V.
Maintenance-free lead-acid battery, GEL, lead-acid Flooded battery :12.6V.