New Volt Amp

Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)

Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)
Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)
Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)
Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)

Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)   Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)

Softub Pump Replacement - Replacement pump for XP2e Aqua Flo Side Discharge Pump. 1.5HP (SPL) 12 Amps, Single (1) Speed with Thermal Wrap Heater Jacket by Hydro Thermix. Motor & Pump with Pre-installed Thermal Wrap. Motor: Manufacture : Century / A.

Smith / Single Speed Motor Horse Power: 1 Service Factor 1.0 (1.5hp SPL) Volts: 115 Amps: 12 RPM: 3450 Frame: 48Y HZ: 60 Stainless Shaft Thermally Protected. Pump: (pre-installed on motor) Manufacture: Aqua-Flo P/N. 1 HP (1.5HP SPL) 1 1/2" Center Suction x Side Discharge - pump threads fit your existing 1.5" pump disconnects/unions. 2 1.5" Female Buttress x 2" Male Buttress Adaptors (These adaptors are included and necessary for pump to fit the existing 2 unions/disconnects) see adaptors installed on pump threads in second picture above.

1 Thermal Wrap Heat Jacket: Pre-installed on motor. (top port on Thermal Wrap is plugged and not used for Softub applications). 32" 3/8" ID Tubing (for making tubing connections between the 2 ports on Thermal Wrap to your existing coil/hose ports in your plumbing).

Note: For 220/230 Volt Softub Pump Replacement. 1 HP, 230 Volts, 50HZ, Single Speed with Pre-Installed "Thermal Wrap" Heater Jacket. More about the Thermal Wrap - Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap. Collecting the heat generated by the pump/motor and recycles that heat to the tub water - were it belongs!

This patented heating system for hot tubs/spas and Whirlpool Baths. Captures and recycles the waste heat "energy" produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature.

The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner.

Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free - no moving parts to wear out. Helps keep motor cooler - increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Self draining design (required for whirlpool bath application). Note: If the pump/connections pictured above do not exactly match the pump have? Give me a call to discuss your application, we either have the pump you need or have other available options that will work for your application.

Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including. Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. Even if you have an electric heater on your spa, the Thermal Wrap System will compliment your electric heater by capturing the waste heat.

The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action.


Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)   Softub Pump 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)